DTC B3920
DTC B3920 |
Diagnostic Instructions |
• |
Perform the
Diagnostic System Check - Vehicle
prior to using this diagnostic procedure.
|
• |
Review
Strategy Based Diagnosis
for an overview of the diagnostic approach.
|
• |
Diagnostic Procedure Instructions
provides an overview of each diagnostic category.
|
DTC Descriptors |
DTC B3920 00
Driver Seat Motors Group 1 Common Circuit Malfunction
DTC B3920 01
Driver Seat Motors Group 1 Common Circuit Short to Battery
DTC B3920 02
Driver Seat Motors Group 1 Common Circuit Short to Ground
DTC B3920 42
Driver Seat Motors Group 1 Common Circuit Calibration Not Programmed
DTC B3920 0B
Driver Seat Motors Group 1 Common Circuit High Current
Diagnostic Fault Information |
Circuit | Short to Ground | High Resistance | Open | Short to Voltage | Signal Performance |
Driver Seat Front Vertical Motor Down Control
|
B3920 02
|
B3920 0B
|
1
|
B3920 01
|
B3920 42
|
Driver Seat Front Vertical Motor Up Control
|
B3920 02
|
B3920 0B
|
1
|
B3920 01
|
B3920 42
|
Driver Seat Rear Vertical Motor Down Control
|
B3920 02
|
B3920 0B
|
1
|
B3920 01
|
B3920 42
|
Driver Seat Rear Vertical Motor Up Control
|
B3920 02
|
B3920 0B
|
1
|
B3920 01
|
B3920 42
|
Driver Seat Horizontal Motor Forward Control
|
B3920 02
|
B3920 0B
|
1
|
B3920 01
|
B3920 42
|
Driver Seat Horizontal Motor Rearward Control
|
B3920 02
|
B3920 0B
|
1
|
B3920 01
|
B3920 42
|
Driver Seat Recline Motor Forward Control
|
B3920 02
|
B3920 0B
|
1
|
B3920 01
|
B3920 42
|
Driver Seat Recline Motor Rearward Control
|
B3920 02
|
B3920 0B
|
1
|
B3920 01
|
B3920 42
|
1. Power Seat Motor Inoperative
|
Circuit/System Description |
The seat memory control module controls the seat motors via half bridges that are connected to power rails internal to the module. The seat memory control module connects all of the motor control circuits on each power rail to a common reference point whenever they are not in operation. This reference point is biased to approximately 2.5 V. The seat memory control module checks to see if this reference voltage is shorted to ground or battery before enabling any seat motor.
When a power seat switch is pressed or when a memory recall is requested, each seat motor receives battery voltage and ground from the seat memory control module via the motor control circuits. All motors are reversible, so the direction the motor rotates depends on which control circuit voltage is applied and which control circuit ground is applied. When the switch is operated in the opposite direction, the module reverses the polarity and applies voltage and ground to the opposite circuits to move the seat in the opposite direction.
Conditions for Running the DTC |
• |
DTC B1325 must not be present.
|
• |
Module battery voltage must be between 9 - 16 V.
|
Conditions for Setting the DTC |
B3920 00
Current out of the module does not match the current returning to the module from 1.5-5A.B3920 01
The voltage on any power rail 1 motor control circuit exceeds 2.78 V for 100 ms.B3920 02
The voltage on any power rail 1 motor control circuit is below 1.47 V for 100 ms.B3920 42
This DTC will set if the module calibration is not programmed.B3920 0B
The differential current measured through the high and low side of the power rail is within tolerance of each other, but the absolute current or an over-current has exceeded the maximum value.Action Taken When the DTC Sets |
The seat memory control module will not allow operation of any motor on the power rail for which the DTC was set.
Conditions for Clearing the DTC |
• |
The current DTC clears when the fault is no longer present and the power mode changes to OFF then back to ACC or RUN.
|
• |
The history DTC will clear after 40 consecutive fault-free ignition cycles have occurred.
|
Reference Information |
Schematic Reference
Driver Seat Schematics
Connector End View Reference
Component Connector End Views
Description and Operation
Memory Seats Description and Operation
Electrical Information Reference
• |
Circuit Testing
|
• |
Connector Repairs
|
• |
Testing for Intermittent Conditions and Poor Connections
|
• |
Wiring Repairs
|
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Testing |
B3920 01 or B3920 02
1. |
Ignition OFF, disconnect the X4, X5 harness connectors at the K40 seat memory control module.
|
2. |
Test for infinite resistance between the control circuit terminals listed below and ground:
|
• |
M50D front vertical motor up control terminal 7 X4
|
• |
M50D front vertical motor down control terminal 8 X4
|
• |
M55D rear vertical motor up control terminal 4 X5
|
• |
M55D rear vertical motor down control terminal 3 X5
|
• |
M51D horizontal motor forward control terminal 2 X5
|
• |
M51D horizontal motor rearward control terminal 1 X5
|
• |
M56D recline motor forward control terminal 5 X5
|
• |
M56D recline motor rearward control terminal 6 X5
|
3. |
If not the specified value, test the control circuit for a short to ground.
|
4. |
Ignition ON, verify that a test lamp does not illuminate between the control circuit terminals listed below and ground:
|
• |
M50D front vertical motor up control terminal 7 X4
|
• |
M50D front vertical motor down control terminal 8 X4
|
• |
M55D rear vertical motor up control terminal 4 X5
|
• |
M55D rear vertical motor down control terminal 3 X5
|
• |
M51D horizontal motor forward control terminal 2 X5
|
• |
M51D horizontal motor rearward control terminal 1 X5
|
• |
M56D recline motor forward control terminal 5 X5
|
• |
M56D recline motor rearward control terminal 6 X5
|
5. |
If the test lamp illuminates, test the control circuit for a short to voltage.
|
6. |
If all circuits test normal, replace the K40 seat memory control module.
|
B3920 00 or B3920 0B
1. |
Ignition ON, use a scan tool to clear the current and history DTC.
|
2. |
Determine which motor set this DTC by operating the driver seat motors listed below one at a time in both directions. Check for the DTC to set between each motor test.
|
• |
M50D seat front vertical motor
|
• |
M55D seat rear vertical motor
|
• |
M51D seat horizontal motor
|
• |
M56D seat back recline motor
|
3. |
Clear the diagnostic trouble code.
|
4. |
Ignition OFF, disconnect the harness connector at the appropriate seat motor for which the DTC set.
|
5. |
Ignition ON, activate the appropriate motor's setting switch in both directions. DTC B3920 00 or B3920 0B must not be set.
|
6. |
If the DTC sets, test for a short between control circuits terminal 1 and terminal 5. If the circuits test normal, replace the K40 seat memory control module.
|
7. |
Test control circuits terminal 1 and terminal 5 for a high resistance. If the circuits test normal, test or replace the seat motor.
|
B3920 42
If this DTC is set, replace the K40 seat memory control module.Repair Instructions |
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
• |
Front Seat Recliner Actuator Motor Replacement (Driver or Passenger Seat 8-Way Power)
|
• |
Front Seat Adjuster Motor Replacement (Driver or Passenger Seat 8-Way Power)
|
• |
Control Module References
for seat memory control module replacement, setup, and programming
|