DTC B2600 or B2605
DTC B2600 or B2605 |
Diagnostic Instructions |
• |
Perform the
Diagnostic System Check - Vehicle
prior to using this diagnostic procedure.
|
• |
Review
Strategy Based Diagnosis
for an overview of the diagnostic approach.
|
• |
Diagnostic Procedure Instructions
provides an overview of each diagnostic category.
|
DTC Descriptor |
DTC B2600 01
Left Daytime Running Lamps Control Circuit Short to Battery
DTC B2600 02
Left Daytime Running Lamps Control Circuit Short to Ground
DTC B2600 04
Left Daytime Running Lamps Control Circuit Open
DTC B2605 01
Right Daytime Running Lamps Control Circuit Short to Battery
DTC B2605 02
Right Daytime Running Lamps Control Circuit Short to Ground
DTC B2605 04
Right Daytime Running Lamps Control Circuit Open
Diagnostic Fault Information |
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
Left Daytime Running Lamps Control | B2600 02 | B2600 04 | B2600 01 | - |
Right Daytime Running Lamps Control | B2605 02 | B2605 04 | B2605 01 | - |
Circuit/System Description |
When the headlight switch is in the Auto position and the ambient light sensor detects sunlight, the body control module (BCM) will command the daytime running lamps to illuminate by providing 12 volts to the daytime running lamp control circuit.
Conditions for Running the DTC |
• |
Engine is running.
|
• |
Headlamp switch in AUTO position.
|
• |
The ambient light is day.
|
Conditions for Setting the DTC |
B2600 01 or B2605 01
The BCM detects a short to voltage on the daytime running lamp control circuitB2600 02 or B2605 04
The BCM detects a short to ground on the daytime running lamp control circuitB2600 04 or B2605 04
The BCM detects an open/high resistance on the daytime running lamp control circuitAction Taken When the DTC Sets |
B2600 01 or B2605 01
The daytime running lamp will be continuously illuminated.B2600 02, B2600 04, B2605 02 or B2605 04
The daytime running lamp will be inoperativeConditions for Clearing the DTC |
• |
The DTC will be current for as long as the fault is present.
|
• |
When the fault is no longer present, the DTC will be a history DTC.
|
• |
A history DTC will clear after 50 ignition cycles.
|
Reference Information |
Schematic Reference
Headlights/Daytime Running Lights (DRL) Schematics
Connector End View Reference
Component Connector End Views
Description and Operation
Exterior Lighting Systems Description and Operation
Electrical Information Reference
• |
Circuit Testing
|
• |
Connector Repairs
|
• |
Testing for Intermittent Conditions and Poor Connections
|
• |
Wiring Repairs
|
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Verification |
Ignition ON, command the Left Dedicated Daytime Running Lamp and the Right Dedicated Daytime Running Lamp ON and OFF with a scan tool. The E4C daytime running lamp - left and the E4D daytime running lamp - right should turn ON and OFF while changing between the commanded states.
Circuit/System Testing |
1. |
Ignition OFF, disconnect the X1 harness connector K9 BCM.
|
2. |
Ignition ON, verify that a test lamp illuminates between the B+ circuit terminal 3 and ground.
|
3. |
If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.
|
4. |
Ignition OFF, connect the X1 harness connector K9 BCM
|
5. |
Ignition OFF, disconnect the inline harness connector listed below:
|
• |
E4C daytime running lamp - left X111 inline harness connector
|
• |
E4D daytime running lamp - right X116 inline harness connector
|
6. |
Connect a test lamp between the control circuit terminal G and ground.
|
7. |
Command the appropriate Dedicated Daytime Running Lamp ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.
|
8. |
If the test lamp is always ON, test the control circuit for a short to voltage. If the circuit tests normal, replace the K9 BCM.
|
9. |
If the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If the circuits test normal, replace the K9 BCM.
|
10. |
If all circuits test normal, replace the daytime running lamp bulb.
|
Repair Instructions |
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
• |
Daytime Running Lamp Bulb Replacement (TT6 Left Side)
|
• |
Control Module References
for BCM replacement, setup, and programming
|