SAAB WIS ONLINE

DTC P0236, P0237, or P0238 (LDK with Turbocharger)

DTC P0236, P0237, or P0238 (LDK with Turbocharger)

Diagnostic Instructions


Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.

Review Strategy Based Diagnosis for an overview of the diagnostic approach.

Diagnostic Procedure Instructions provides an overview of each diagnostic category.


DTC Descriptors

DTC P0236

Turbocharger Boost System Performance

DTC P0237

Turbocharger Boost Sensor Circuit Low Voltage

DTC P0238

Turbocharger Boost Sensor Circuit High Voltage

Diagnostic Fault Information

Circuit Short to Ground High Resistance Open Short to Voltage Signal Performance
5 V Reference

P0107, P0193, P0236, P0642

P0236, P0237

P0107, P0236

P0036, P0193, P0236, P050 P0606, P0643

P0234, P0236, P0299

Intake Air Pressure Signal

P0237

P0236, P0237

P0238

P0238

P0236

Low Reference

-

P0234, P0236, P0238

P0098, P0099, P0238

-

-



Typical Scan Tool Data

Boost Pressure Sensor

Circuit Short to Ground Open Short to Voltage
Operating Conditions: Engine running at various operating conditions

Parameter Normal Range: BARO to 240 kPa

5 V Reference

20-80 kPa

30-80 kPa

20-80 kPa

Boost Pressure Sensor

0 kPa

276 kPa

276 kPa

Low Reference

-

276 kPa

-



Circuit Description

The air intake pressure sensor is integrated with the intake air temperature sensor 2 (IAT). The air intake pressure sensor measures the range of pressures between the turbocharger and the throttle body. The sensor used on this engine is a three atmosphere sensor. Pressure in this portion of the induction system is affected by engine speed, throttle opening, turbocharger boost pressure, intake air temperature (IAT), barometric pressure (BARO), and the efficiency of the charge air cooler (CAC). The intake air pressure and temperature sensor has the following circuits:


5 Volt Reference

Low Reference

Intake Air Pressure Signal

IAT Sensor 2 Signal


The sensor provides a signal voltage to the engine control module (ECM), relative to the pressure changes, on the intake air pressure signal circuit. Under normal operation the greatest pressure that can exist in this portion of the induction system at ignition ON, engine OFF is equal to the BARO. When the vehicle is operated at wide-open throttle (WOT) the turbocharger can increase the pressure to near 240 kPa. The least pressure that occurs is when the vehicle is idling or decelerating, and it is equal to the BARO.

Conditions for Running the DTC


P0236 - Engine Cranking

DTCs P0107, P0108, P0121, P0122, P0123, P0221, P0222, P0223, P0237, P0238, P2227, P2228, or P2229 are not set.

The engine OFF timer is greater than 4 s.

The engine is cranking at less than 400 RPM for at least 200 ms.

This DTC runs during engine cranking only.



P0236 - Engine Idling

DTCs P0121, P0122, P0123, P0221, P0222, P0223, P0237, P0238, P2227, P2228, or P2229 are not set.

The engine is running and the ECM has counted greater than three revolutions.

The engine speed is less than 1000 RPM.

The TP Sensor parameter is less than 24 %.

The ECM is not in limp home mode.

This DTC runs continuously within the enabling conditions.



P0237

The ignition is ON or the engine is running.

This DTC runs continuously within the enabling conditions.



P0238

The ignition is ON or the engine is running.

This DTC runs continuously within the enabling conditions.


Conditions for Setting the DTC

P0236 - Engine Cranking

The ECM detects when the engine is cranking that the boost pressure sensor signal plus a calibrated threshold is not within range of a model derived from the BARO sensor, the MAP sensor, and the boost pressure sensor for more than 2 s.


P0236 - Engine Idling

The ECM detects when the engine is idling that the boost pressure sensor signal is less than 50 kPa for greater than 4 s continuously, or 50 s cumulative.

OR

The ECM detects when the engine is idling that the boost pressure sensor signal plus a calibrated threshold is not within range of the BARO sensor for greater than 4 s continuously, or 50 s cumulative.


P0237

The ECM detects that the boost pressure sensor voltage is less than 0.19 V for more than 4 s continuously, or 50 s cumulative.

P0238

The ECM detects that the boost pressure sensor voltage is greater than 4.85 V for more than 4 s continuously, or 50 s cumulative.

Action Taken When the DTC Sets


DTCs P0236, P0237, P0238 are Type B DTCs.

The ECM will disable boost control and limit the system to mechanical boost only, resulting in a substantial decrease in engine power.


Conditions for Clearing the MIL/DTC

DTCs P0236, P0237, P0238 are Type B DTCs.

Diagnostic Aids


The intake air pressure sensor signal circuit is pulled high in the ECM. With the sensor disconnected, at ignition ON, a normal voltage measurement of the signal circuit with a DMM is 5.60 V.

The CAC is connected to the turbocharger and to the throttle body by flexible duct work that requires the use of special high torque fastening clamps. These clamps cannot be substituted. In order to prevent any type of air leak when servicing the ductwork, the tightening specifications and proper positioning of the clamps is critical and must be strictly adhered to.

Use a solution of dish soap and water in a spray bottle to pinpoint any air leaks.

The BARO sensor is integrated within the ECM, and it has a port on the housing that allows it to sense the ambient pressure. Any restriction at this opening may hinder the operation of the BARO sensor.


Reference Information

Schematic Reference

Engine Controls Schematics

Connector End View Reference

Component Connector End Views

Description and Operation


Boost Control System Description (LDK with Turbocharger)

Turbocharger System Description (LDK with Turbocharger)


Electrical Information Reference


Circuit Testing

Connector Repairs

Testing for Intermittent Conditions and Poor Connections

Wiring Repairs


DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification


1. Verify that DTCs P0641, P0642, or P0643 are not set.

2. If any of the DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle .

3. Ignition OFF for 90 s. Determine the current vehicle testing altitude. Ignition ON, observe the scan tool MAP Sensor parameter, the Boost Pressure Sensor parameter, and the BARO Sensor parameter. Compare the parameters to each other and to the Altitude Versus Barometric Pressure table.

4. Engine idling, observe the scan tool and compare the Boost Pressure Sensor parameter to the BARO Sensor parameter. They should be within 4 kPa of each other.

5. Use the scan tool and compare the MAP Sensor parameter to the Boost Pressure Sensor parameter during a WOT acceleration at the time of the 1-2 shift. The readings should be within 20 kPa of each other.

6. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.


Circuit/System Testing


1. Verify the integrity of the entire air induction system including all turbocharger components by inspecting for the following conditions:

Any damaged components

Hairline fractures of the boost pressure sensor housing

Hairline fractures of the MAP sensor housing

A buildup of contamination, snow or ice at the BARO port on the ECM

Loose or improper installation

An air flow restriction

Any vacuum leak

Any type of air leak between the turbocharger and the throttle body, including the CAC assembly.

Verify that an exhaust leak does not exist, including the mating surface area between the turbocharger and the exhaust manifold.

2. Ignition OFF for 90 s, disconnect the harness connector at the intake air pressure and temperature sensor.

3. Test for less than 5 Ω between the low reference circuit terminal 1 or A and ground.

4. If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the K20 ECM.

5. Ignition ON, test for 4.8-5.2 V between the 5 V reference circuit terminal 3 or C and ground.

6. If less than the specified range, test the 5 V reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the K20 ECM.

7. If greater than the specified range, test the 5 V reference circuit for a short to voltage. If the circuit tests normal, replace the K20 ECM.

8. Verify the scan tool Boost Pressure Sensor parameter is greater than 275 kPa.

9. If less than the specified range, test the signal circuit terminal 4 or D for a short to ground. If the circuit tests normal, replace the K20 ECM.

10. Install a 3 A fused jumper wire between the signal circuit terminal 4 or D and the low reference circuit terminal 1 or A. Verify the scan tool Boost Pressure Sensor parameter is less than 1 kPa.

11. If greater than the specified range, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the K20 ECM.

12. If the circuits test normal, test or replace the B65 intake air pressure and temperature sensor.


Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.


Intake Air Pressure and Temperature Sensor Replacement

Control Module References for ECM replacement, setup, and programming