DTC B0987
DTC B0987 |
Diagnostic Instructions |
• |
Perform the
Diagnostic System Check - Vehicle
prior to using this diagnostic procedure.
|
• |
Review
Strategy Based Diagnosis
for an overview of the diagnostic approach.
|
• |
Diagnostic Procedure Instructions
provides an overview of each diagnostic category.
|
DTC Descriptor |
DTC B0987 05
Vehicle Direction Camera Indicator Circuit High Voltage/Open
Diagnostic Fault Information |
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
Lane Departure Warning Switch Indicator Ignition
|
B0987 05
|
B0987 05
|
-
|
-
|
Lane Departure Warning Switch Indicator Control
|
-
|
B0987 05
|
B0987 05
|
-
|
Lane Departure Warning Switch Ground
|
-
|
B356A 05
|
-
|
-
|
Circuit/System Description |
The lane departure warning is enabled and disabled through a switch located in the multifunction switch at the instrument panel. When enabled, the vehicle direction camera control module will illuminate the indicator located in the switch.
Conditions for Running the DTC |
Ignition ON
Conditions for Setting the DTC |
The vehicle direction camera control module has detected a short to battery or open.
Action Taken When the DTC Sets |
• |
Lane departure warning is disabled.
|
• |
SERVICE LANE DEPARTURE SYSTEM is displayed on the driver information center.
|
Conditions for Clearing the DTC |
The condition for setting the DTC is no longer present.
Reference Information |
Schematic Reference
Object Detection Schematics
Connector End View Reference
Component Connector End Views
Description and Operation
Object Detection Description and Operation (Parking Assist) Object Detection Description and Operation (Lane Departure Warning) Object Detection Description and Operation (Parking Assist with Parallel Parking) Object Detection Description and Operation (Traffic Sign Assist)
Electrical Information Reference
• |
Circuit Testing
|
• |
Connector Repairs
|
• |
Testing for Intermittent Conditions and Poor Connections
|
• |
Wiring Repairs
|
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Verification |
1. |
Verify DTC B356A is not set.
|
2. |
If DTC is set, refer to
DTC B356A
.
|
3. |
Verify DTC B0987 is not set.
|
4. |
If DTC is set, refer to Circuit/System Testing.
|
Circuit/System Testing |
1. |
Ignition OFF, disconnect the harness connector at the K74 Vehicle Direction Camera Control Module and the harness connector at the S48D Multifunction Switch 2 - Instrument Panel.
|
2. |
Ignition ON, test for greater than 11 V between the ignition circuit terminal 3 at the S48D Multifunction Switch 2 - Instrument Panel harness connector and ground.
|
3. |
If less than the specified value, test the ignition circuit for a short to ground or an open/high resistance.
|
4. |
Test for less than 0.3 V between the control circuit terminal 8 at the S48D Multifunction Switch 2 - Instrument Panel harness connector and ground.
|
5. |
If greater than the specified value, test the control circuit for a short to voltage.
|
6. |
Ignition OFF, test for infinite resistance between the control circuit terminal 8 at the S48D Multifunction Switch 2 - Instrument Panel harness connector and ground.
|
7. |
If less than the specified value, test control circuit for a short to ground.
|
8. |
Test for less than 5 Ω between the S48D Multifunction Switch 2 - Instrument Panel control circuit terminal 8 and the control circuit terminal 4 at the K74 Vehicle Direction Camera Control Module harness connector
|
9. |
If greater than the specified value, test the control circuit for an open/high resistance.
|
10. |
If all circuits test normal, connect the harness connector to the K74 Vehicle Direction Camera Control Module, replace the S48D Multifunction Switch 2 - Instrument Panel and verify the DTC does not reset.
|
11. |
If the DTC resets, replace the K74 Vehicle Direction Camera Control Module.
|
Repair Instructions |
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
• |
Front Floor Console Multifunction Switch Replacement
|
• |
Control Module References
for vehicle direction camera control module replacement, setup and programming
|