Engine Replacement (AWD)
Engine Replacement (AWD) |
Special Tools
• |
CH-49289
Blue Tool
|
• |
CH-49290
Orange Tool
|
For equivalent regional tools, refer to Special Tools (LDK, LHU) .
Removal Procedure |
1. |
Turn the ignition OFF.
|
2. |
Remove the intermediate steering shaft fastener. Refer to
Intermediate Steering Shaft Replacement
.
|
3. |
Remove the fuel injector sight shield. Refer to
Fuel Injector Sight Shield Replacement
.
|
4. |
Evacuate the air conditioning system. Refer to
Refrigerant Recovery and Recharging
.
|
5. |
Remove the engine control module. Refer to
Engine Control Module Replacement
.
|
6. |
Remove the battery tray. Refer to
Battery Tray Replacement (Diesel)
Battery Tray Replacement (LHU/A20NFT)
.
|
7. |
Remove the air cleaner outlet duct. Refer to
Air Cleaner Outlet Duct Replacement
.
|
8. |
Remove the air cleaner assembly. Refer to
Air Cleaner Assembly Replacement
.
|
9. |
Remove the charge air cooler air inlet hose and the charge air cooler air outlet hose. Refer to
Charge Air Cooler Inlet Air Hose Replacement
and
Charge Air Cooler Outlet Air Hose Replacement
.
|
10. |
Drain the cooling system. Refer to
Cooling System Draining and Filling (LAU/A28NER)
Cooling System Draining and Filling (LBS/A20DTH)
Cooling System Draining and Filling (LHU/A20NFT)
.
|
11. |
Disconnect the engine wiring harness connectors (1, 2, 3).
|
12. |
Remove the engine wiring harness ground connectors (1) from the front end upper tie bar support.
|
13. |
Remove the engine wiring harness (1) from the front compartment fuse block housing (2).
|
14. |
Position and secure the wiring harness to the engine.
|
15. |
Remove the radiator surge tank hoses from the radiator surge tank. Refer to
Radiator Surge Tank Engine Hose Replacement
.
|
16. |
Position and secure the surge tank hoses to the engine.
|
17. |
Remove the engine coolant air bleed hose. Refer to
Engine Coolant Air Bleed Hose Replacement (Diesel)
Engine Coolant Air Bleed Hose Replacement (LHU/A20NFT)
.
|
18. |
Remove the manual transmission shift lever cable from the transmission. Refer to
Range Selector Lever Cable Replacement
.
|
19. |
Position and secure the manual transmission shift lever cable to the vehicle.
|
20. |
Remove the power brake booster pipe (1) from the power brake booster (2).
|
21. |
Remove the heater inlet hose and the heater outlet hose from the heater core. Refer to
Heater Inlet Hose Replacement (Diesel)
Heater Inlet Hose Replacement (LAU/A28NER)
Heater Inlet Hose Replacement (LLU/A16LET)
Heater Inlet Hose Replacement (LHU/A20NFT)
and
Heater Outlet Hose Replacement (Diesel)
Heater Outlet Hose Replacement (LAU/A28NER)
Heater Outlet Hose Replacement (LLU/A16LET)
Heater Outlet Hose Replacement (LHU/A20NFT)
.
|
22. |
Relieve the fuel system pressure. Refer to
Fuel Pressure Relief
.
|
23. |
Remove the fuel feed front pipe. Refer to
Fuel Feed Pipe Replacement (Metal)
Fuel Feed Pipe Replacement (Plastic)
.
|
24. |
Disconnect the evaporative pipe quick connector (1).
|
26. |
Raise and support the vehicle. Refer to
Lifting and Jacking the Vehicle
.
|
27. |
Remove the front wheels. Refer to
Tire and Wheel Removal and Installation
.
|
28. |
Remove the both front wheel drive shaft fasteners. Refer to
Front Wheel Drive Shaft Replacement - Right Side (GNB)
Front Wheel Drive Shaft Replacement - Right Side (Petrol)
and
Front Wheel Drive Shaft Replacement - Left Side (GNA)
Front Wheel Drive Shaft Replacement - Left Side (GNB)
.
|
29. |
Remove the stabilizer shaft link fasteners. Refer to
Stabilizer Shaft Link Replacement (GNA)
Stabilizer Shaft Link Replacement (GNB)
.
|
30. |
Remove the steering linkage outer tie rod fasteners. Refer to
Steering Linkage Outer Tie Rod Replacement
.
|
31. |
Remove both steering knuckles from both front lower control arms. Refer to
Steering Knuckle Replacement (GNA)
Steering Knuckle Replacement (GNB)
.
|
32. |
Remove both front wheel drive shafts from both front wheel bearings and hubs. Refer to
Front Wheel Bearing and Hub Replacement (GNA)
Front Wheel Bearing and Hub Replacement (GNB)
.
|
33. |
Disconnect both front wheel speed sensor electrical connectors. Position and secure both wiring harnesses to the vehicle. Refer to
Front Wheel Speed Sensor Replacement (GNA)
Front Wheel Speed Sensor Replacement (GNB)
.
|
34. |
Disconnect the power steering wiring harness connector (2).
|
35. |
Disconnect the engine coolant fan motor wiring harness connectors (1).
|
36. |
Remove the relay box (1).
|
37. |
Position and secure the relay box to the engine.
|
38. |
Remove the propeller shaft. Refer to
Propeller Shaft Replacement
.
|
39. |
Remove exhaust front pipe. Refer to
Exhaust Front Pipe Replacement
.
|
40. |
If available both drivetrain and front suspension frame transmission protectors.
|
41. |
Remove the engine shield from the front suspension frame.
|
42. |
Raise the vehicle enough to place a suitable lift table under the engine, transmission, front frame and front suspension assembly.
|
43. |
Position a suitable powertrain or engine lift table below the frame, engine and transmission.
|
45. |
Remove the powertrain lift/support table.
|
46. |
Lower the vehicle.
|
47. |
Remove the engine mount bracket from the engine mount support. Refer to
Engine Mount Bracket Replacement
.
|
48. |
Remove the transmission mount fasteners. Refer to
Transmission Mount Replacement - Left Side
.
|
49. |
Raise the vehicle.
|
51. |
Raise the lift table or lower the vehicle to support the frame, engine and transmission.
|
52. |
Check if wheel alignment is required. |
• |
Move out position pins (1) and try to insert into underbody holes.
|
• |
If guide pins can NOT be inserted, the
Wheel Alignment Measurement
is required after installation of drive train frame.
|
53. |
Remove the front suspension frame fasteners. Refer to
Drivetrain and Front Suspension Frame Front Crossmember Replacement (GNA)
Drivetrain and Front Suspension Frame Front Crossmember Replacement (GNB)
.
|
54. |
With the aid of an assistant, lower the table or raise the vehicle to remove the engine, transmission, front frame and front suspension assembly from the vehicle. |
55. |
Remove the power steering pressure pipe/hose from the power steering pump. Refer to
Power Steering Pressure Pipe/Hose Replacement (L4)
Power Steering Pressure Pipe/Hose Replacement (V6)
.
|
56. |
Remove the power steering return hose from the power steering gear. Refer to
Power Steering Return Hose Replacement (L4)
Power Steering Return Hose Replacement (V6)
.
|
57. |
Remove the charge air cooler inlet air hose and the charge air cooler outlet hose from the charge air cooler. Refer to
Charge Air Cooler Radiator Replacement (Diesel)
Charge Air Cooler Radiator Replacement (LAU/A28NER)
Charge Air Cooler Radiator Replacement (LLU/A16LET)
Charge Air Cooler Radiator Replacement (LHU/A20NFT)
.
|
58. |
Remove the radiator inlet hose. Refer to
Radiator Inlet Hose Replacement (Diesel)
Radiator Inlet Hose Replacement (LAU/A28NER)
Radiator Inlet Hose Replacement (LHU/A20NFT)
.
|
59. |
Remove the radiator outlet hose. Refer to
Radiator Outlet Hose Replacement (Diesel)
Radiator Outlet Hose Replacement (LAU/A28NER)
Radiator Outlet Hose Replacement (LHU/A20NFT)
.
|
60. |
Remove the engine cooling module wiring harness from the drivetrain and front suspension frame.
|
61. |
Remove the engine wiring harness from the radiator.
|
62. |
Remove the engine cooling module from the drivetrain and front suspension frame.
|
63. |
Remove both front wheel drive shafts from the transmission. Refer to
Front Wheel Drive Shaft Replacement - Right Side (GNB)
Front Wheel Drive Shaft Replacement - Right Side (Petrol)
and
Front Wheel Drive Shaft Replacement - Left Side (GNA)
Front Wheel Drive Shaft Replacement - Left Side (GNB)
.
|
64. |
Connect a floor crane to the engine lift brackets and raise the floor crane to partially support the engine.
|
65. |
Remove the transmission rear mount fasteners from the drivetrain and front suspension frame. Refer to
Transmission Rear Mount Replacement
.
|
66. |
Remove the transmission front mount fasteners from the drivetrain and front suspension frame. Refer to
Transmission Front Mount Replacement
.
|
67. |
Remove the engine and the transmission from the drivetrain and front suspension frame.
|
68. |
Remove the transmission rear mount bracket and the transfer case. Refer to
Transfer Case Assembly Replacement
.
|
69. |
Remove the transmission front mount. Refer to
Transmission Front Mount Replacement
.
|
70. |
Remove the starter motor Refer to
Starter Replacement (2.0L Diesel)
Starter Replacement (LAU/A28NER)
Starter Replacement (LDE/A16XER, LLU/A16LET, 2H0/A18XER)
Starter Replacement (LHU/A20NFT)
.
|
71. |
Install two transmission lift brackets to the transmission housing.
|
72. |
Position a second floor crane to the transmission lift brackets and raise the floor crane to partially support the transmission.
|
73. |
Remove the transmission from the engine. Refer to
Transmission Replacement (FWD, LBS/A20DTH)
Transmission Replacement (All Wheel Drive - LBY/A20DTR)
Transmission Replacement (Front Wheel Drive - LBY/A20DTR)
Transmission Replacement (AWD, LHU/A20NFT)
Transmission Replacement (FWD, LHU/A20NFT)
.
|
Installation Procedure |
2. |
Position a second floor crane to the transmission lift brackets and raise the floor crane to partially support the transmission.
|
3. |
Install two transmission lift brackets to the transmission housing.
|
4. |
Install the starter. Refer to
Starter Replacement (2.0L Diesel)
Starter Replacement (LAU/A28NER)
Starter Replacement (LDE/A16XER, LLU/A16LET, 2H0/A18XER)
Starter Replacement (LHU/A20NFT)
.
|
5. |
Install the transmission front mount fasteners from the drivetrain and front suspension frame. Refer to
Transmission Front Mount Replacement
.
|
6. |
Install the transmission rear mount fasteners from the drivetrain and front suspension frame. Refer to
Transmission Rear Mount Replacement
.
|
7. |
Install the engine and the transmission from the drivetrain and front suspension frame.
|
8. |
Connect a floor crane to the engine lift brackets and raise the floor crane to partially support the engine.
|
9. |
Install both front wheel drive shafts from the transmission. Refer to
Front Wheel Drive Shaft Replacement - Right Side (GNB)
Front Wheel Drive Shaft Replacement - Right Side (Petrol)
and
Front Wheel Drive Shaft Replacement - Left Side (GNA)
Front Wheel Drive Shaft Replacement - Left Side (GNB)
.
|
10. |
Install the engine cooling module from the drivetrain and front suspension frame.
|
11. |
Install the engine wiring harness from the radiator.
|
12. |
Install the engine cooling module wiring harness from the drivetrain and front suspension frame.
|
13. |
Install the radiator outlet hose. Refer to
Radiator Outlet Hose Replacement (Diesel)
Radiator Outlet Hose Replacement (LAU/A28NER)
Radiator Outlet Hose Replacement (LHU/A20NFT)
.
|
14. |
Install the radiator inlet hose. Refer to
Radiator Inlet Hose Replacement (Diesel)
Radiator Inlet Hose Replacement (LAU/A28NER)
Radiator Inlet Hose Replacement (LHU/A20NFT)
.
|
15. |
Install the charge air cooler inlet air hose and the charge air cooler outlet hose from the charge air cooler. Refer to
Charge Air Cooler Radiator Replacement (Diesel)
Charge Air Cooler Radiator Replacement (LAU/A28NER)
Charge Air Cooler Radiator Replacement (LLU/A16LET)
Charge Air Cooler Radiator Replacement (LHU/A20NFT)
.
|
16. |
Install the power steering return hose to the power steering pump. Refer to
Power Steering Return Hose Replacement (L4)
Power Steering Return Hose Replacement (V6)
.
|
17. |
Install the power steering pressure pipe/hose to the power steering pump. Refer to
Power Steering Pressure Pipe/Hose Replacement (L4)
Power Steering Pressure Pipe/Hose Replacement (V6)
.
|
18. |
With the aid of an assistant, lower the table or raise the vehicle to remove the engine, transmission, front frame and front suspension assembly from the vehicle.
|
19. |
Install the front suspension frame fasteners. Refer to
Drivetrain and Front Suspension Frame Insulator Replacement
.
|
20. |
Raise the lift table or lower the vehicle to support the frame, engine and transmission.
|
22. |
Raise the vehicle.
|
23. |
Install the transmission mount fasteners. Refer to
Transmission Mount Replacement - Left Side
.
|
24. |
Install the engine mount bracket to the engine mount support. Refer to
Engine Mount Bracket Replacement
.
|
25. |
Lower the vehicle.
|
26. |
Install the powertrain lift/support table.
|
28. |
Position a suitable powertrain or engine lift table below the frame, engine and transmission.
|
29. |
Raise the vehicle enough to place a suitable lift table under the engine, transmission, front frame and front suspension assembly.
|
30. |
Install the engine shield from the front suspension frame.
|
31. |
If available install both drivetrain and front suspension frame transmission protectors.
|
32. |
Install the exhaust front pipe. Refer to
Exhaust Front Pipe Replacement
.
|
33. |
Install the propeller shaft. Refer to
Propeller Shaft Replacement
.
|
34. |
Position and secure the relay box to the engine.
|
35. |
Install the relay box (1).
|
36. |
Connect the power steering wiring harness connector (2).
|
37. |
Connect the engine coolant fan motor wiring harness connectors (1).
|
38. |
Connect both front wheel speed sensor electrical connectors. Position and secure both wiring harnesses to the vehicle. Refer to
Front Wheel Speed Sensor Replacement (GNA)
Front Wheel Speed Sensor Replacement (GNB)
.
|
39. |
Install both front wheel drive shafts from both front wheel bearings and hubs. Refer to
Front Wheel Bearing and Hub Replacement (GNA)
Front Wheel Bearing and Hub Replacement (GNB)
.
|
40. |
Install both steering knuckles to both front lower control arms. Refer to
Steering Knuckle Replacement (GNA)
Steering Knuckle Replacement (GNB)
.
|
41. |
Install the steering linkage outer tie rod fasteners. Refer to
Steering Linkage Outer Tie Rod Replacement
.
|
42. |
Install the stabilizer shaft link fasteners. Refer to
Stabilizer Shaft Link Replacement (GNA)
Stabilizer Shaft Link Replacement (GNB)
.
|
43. |
Install the front wheel drive shaft fasteners. Refer to
Front Wheel Drive Shaft Replacement - Right Side (GNB)
Front Wheel Drive Shaft Replacement - Right Side (Petrol)
and
Front Wheel Drive Shaft Replacement - Left Side (GNA)
Front Wheel Drive Shaft Replacement - Left Side (GNB)
.
|
44. |
Install the front wheels. Refer to
Tire and Wheel Removal and Installation
.
|
45. |
Raise and support the vehicle. Refer to
Lifting and Jacking the Vehicle
.
|
47. |
Connect the evaporative pipe quick connector (1).
|
48. |
Plug the fuel feed pipe and cap the fuel injection fuel rail to prevent fuel loss or contamination.
|
49. |
Install the fuel feed front pipe. Refer to
Fuel Feed Pipe Replacement (Metal)
Fuel Feed Pipe Replacement (Plastic)
.
|
50. |
Install the heater inlet hose and the heater outlet hose from the heater core. Refer to
Heater Inlet Hose Replacement (Diesel)
Heater Inlet Hose Replacement (LAU/A28NER)
Heater Inlet Hose Replacement (LLU/A16LET)
Heater Inlet Hose Replacement (LHU/A20NFT)
and
Heater Outlet Hose Replacement (Diesel)
Heater Outlet Hose Replacement (LAU/A28NER)
Heater Outlet Hose Replacement (LLU/A16LET)
Heater Outlet Hose Replacement (LHU/A20NFT)
.
|
51. |
Relieve the fuel system pressure. Refer to
Fuel Pressure Relief
.
|
52. |
Install the power brake booster pipe (1) from the power brake booster (2).
|
53. |
Position and secure the manual transmission shift lever cable to the vehicle.
|
54. |
Install the manual transmission shift lever cable to the transmission. Refer to
Range Selector Lever Cable Replacement
.
|
55. |
Install the engine coolant air bleed hose. Refer to
Engine Coolant Air Bleed Hose Replacement (Diesel)
Engine Coolant Air Bleed Hose Replacement (LHU/A20NFT)
.
|
56. |
Install the radiator surge tank hoses from the radiator surge tank. Refer to
Radiator Surge Tank Engine Hose Replacement
.
|
57. |
Install the engine wiring harness (1) to the front compartment fuse block housing (2).
|
58. |
Install the engine wiring harness ground connectors (1) from the front end upper tie bar support.
|
59. |
Connect the engine wiring harness connectors (1, 2, 3).
|
60. |
Fill the cooling system. Refer to
Cooling System Draining and Filling (LAU/A28NER)
Cooling System Draining and Filling (LBS/A20DTH)
Cooling System Draining and Filling (LHU/A20NFT)
.
|
61. |
Install the charge air cooler air inlet hose and the charge air cooler air outlet hose. Refer to
Charge Air Cooler Inlet Air Hose Replacement
and
Charge Air Cooler Outlet Air Hose Replacement
.
|
62. |
Install the air cleaner assembly. Refer to
Air Cleaner Assembly Replacement
.
|
63. |
Install the air cleaner outlet duct. Refer to
Air Cleaner Outlet Duct Replacement
.
|
64. |
Install the battery tray. Refer to
Battery Tray Replacement (Diesel)
Battery Tray Replacement (LHU/A20NFT)
.
|
65. |
Install the engine control module. Refer to
Engine Control Module Replacement
.
|
66. |
Evacuate the air conditioning system. Refer to
Refrigerant Recovery and Recharging
.
|
67. |
Install the engine sight shield. Refer to
Engine Sight Shield Replacement
.
|
68. |
Install the intermediate steering shaft fastener. Refer to
Intermediate Steering Shaft Replacement
.
|